top of page
ormity-logo-1600px.png
Stainless steel M5 threaded micro-nozzle for IPX1 IPX2 drip box

Drip Box Nozzles: Why Needles Fail and Threaded Stainless Micro-Nozzles Last (IPX1 / IPX2)

Nov 6
3 min read

A drip box is only as good as its drip points. IEC 60529 asks for a regular grid of drops above the specimen, at a measured rainfall of 1 mm/min for IPX1 and 3 mm/min for IPX2. The manifold, the water supply and the calibration all matter, but the hundreds of small parts that actually form the drops are where most drip boxes go wrong. This technical note explains why, and why we made a different choice.

What most drip boxes use as nozzles

Look under a typical IPX1 / IPX2 drip box and you will usually find one of three solutions:

  • Adapted hypodermic needles, cut to length and fitted into the plate.

  • Technical pen tips (the fine metal tips of ink drawing pens), used as calibrated tubes.

  • Hybrid parts: a plastic body or plastic thread moulded or glued onto a cut steel needle.

They are cheap and easy to source. They also share the same weaknesses.

Problem 1: the grid does not stay a grid

A needle is a long, thin, unsupported tube. It bends when the box is cleaned, handled, transported or simply brushed against during set-up. Once a few needles are bent, the drops no longer fall on the 20 × 20 mm pattern: some areas receive two drops, others none. The average rainfall measured in a collecting tray may still look correct, while the distribution over the specimen is not. For a test that is meant to reproduce uniform dripping water, a drifting grid is a hidden error.

Problem 2: a drip box full of needles is a safety hazard

A drip box is installed above head height and handled by people. If it is dropped, or if someone puts a hand under it while adjusting a specimen, rigid needle points can penetrate the skin, and in a bad accident go through a hand.

Our micro-nozzles have no sharp point. The maximum possible insertion is about 1 mm, and in practice close to zero, because the skin flexes before anything penetrates. Laboratory safety should not depend on nobody ever dropping the box.

Problem 3: needles are not designed to be cleaned and reused

Every drip box eventually clogs: a mineral deposit, a particle from the supply line, a biofilm after a long idle period. What happens next depends on how the drip points are mounted:

  • Needles inserted from the inside of the box: you have to open a cover, unglue the blocked needles and fit new ones, then reseal the box.

  • Needles with a plastic thread over the steel: the plastic threads strip after one or two removals, so the part is effectively single-use.

  • Plastic-to-steel joints in an ultrasonic bath: the glue or overmoulded joint between plastic and needle tends to loosen over repeated cleaning cycles, until the needle moves or leaks.

In each case, the routine cleaning that the test requires slowly degrades the drip box itself.

Our approach: threaded M5 stainless steel micro-nozzles

Every Ormity and Dunel drip box manifold uses machined micro-nozzles:

Animated render: stainless steel M5 micro-nozzle screwed into an Ormity drip box manifold
The M5 micro-nozzle screws into the manifold from the outside: no cover to open, no glue, no plastic thread.
  • All stainless steel: body, thread and orifice are one part. No plastic, no glue, no joint to fail.

  • M5 thread: each nozzle screws into the manifold from the outside. Removing one does not require opening the box.

  • Ø 0.4 mm orifice: a defined drop-forming geometry on every point of the grid.

  • Short and rigid: the nozzle does not bend, so the 20 × 20 mm grid stays where it was built.

  • Ultrasonic-cleanable: unscrew the nozzles, put them in an ultrasonic bath, screw them back. They are ready to use again, cycle after cycle.

  • Individually replaceable: a damaged nozzle is replaced alone, with a spare M5 micro-nozzle, not a whole plate.

A stainless micro-nozzle costs a little more than a needle. Over the life of the equipment it costs far less, because it is cleaned and reused instead of being replaced, and because the test conditions stay valid between calibrations.

Keeping the nozzles clean

The 0.4 mm orifice is small on purpose, so water quality matters. Use demineralized or filtered water, drain the box after use, and include a periodic ultrasonic cleaning of the nozzles in your maintenance plan. After cleaning, verify the rainfall with a collecting tray; our IPX1 / IPX2 pluviometer page describes the method.

Proven in the field

These are some of the reasons why more than 1,500 Ormity and Dunel drip box manifolds, of all sizes, have been installed in laboratories around the world over the last 15 years.

Related resources

Comments


Commenting on this post isn't available anymore. Contact the site owner for more info.
bottom of page