top of page
ormity-logo-1600px.png
Abstract diagonal blue stripes background

PRODUCT

Home   /   Product

Zand- en stoftestkamer MIL-STD-810H

Productcode ORTYDC810-MIL
Prijs

C$ 0,00

Dual-function sand and dust test chamber for MIL-STD-810H Method 510.7. It runs blowing sand (Procedure II) at high air velocity and, after the sand is removed and the circuit cleaned, blowing dust (Procedure I) at reduced fan speed – one machine for both procedures.

Normen

  • MIL-STD-810H – Method 510.7, Procedure I blowing dust and Procedure II blowing sand
  • IEC 60068-2-68 – dust and sand tests
  • IEC 60529 / ISO 20653 (with IP configuration)

Technische gegevens

Functies Dual: blowing sand (Proc. II) and blowing dust (Proc. I); sand removed and circuit cleaned before dust tests
Air circuit Closed-loop stainless steel wind tunnel, variable-speed centrifugal fan, sand collection hopper under the test section (sand not re-circulated through the fan)
Air velocity Adjustable, up to 29 m/s
Temperatuur Heating system with temperature control for the high-temperature exposure
Humidity control Dehumidifiers in the ducting and in the sand hopper (RH ≤ 30 % for dust tests, free-flowing sand)
Stofconcentratie Measured in the test section with an optical particle-concentration meter
Proc. I – air velocity 8.9 ± 1.3 m/s (1750 ± 250 ft/min); 1.5 ± 1 m/s during temperature conditioning
Proc. I – dust concentration 10.6 ± 7 g/m³ (0.3 ± 0.2 g/ft³)
Proc. I – dust 100 % < 150 µm, median 20 ± 5 µm (e.g. 140-mesh silica flour)
Proc. I – relative humidity ≤ 30 % RH
Proc. I – duration ≥ 6 h at standard ambient + ≥ 6 h at high temperature
Proc. II – air velocity 18–29 m/s at impact (40–65 mph); about 3 m from injection to specimen
Proc. II – sand concentration 2.2 ± 0.5 g/m³ near aircraft · 1.1 ± 0.3 g/m³ near surface vehicles · 0.18 (−0/+0.2) g/m³ natural conditions
Proc. II – sand quartz sand ≥ 95 % SiO₂, 150–850 µm
Proc. II – duration ≥ 90 min per vulnerable face
Afmeting proefstuk ≤ 50 % of cross-section, ≤ 30 % of volume
Besturing PLC with touch HMI, fan speed setting, configurable test profiles, data logging, emergency stop
Constructie SS304 test section and ducting, abrasion-resistant air paths, viewing window, stainless steel base frame on levelling feet

Ref.: ORTYDC810-MIL

Aantal

Testprincipe & werking

MIL-STD-810H Method 510.7 has two procedures. Procedure I (blowing dust, particles < 150 µm) evaluates resistance to dust penetration into cracks, crevices, bearings and joints, and the effect on filters. Procedure II (blowing sand, 150–850 µm) evaluates erosion and clogging caused by sharp-edged particles driven at desert-wind speeds.

The chamber is a closed-loop wind tunnel: a variable-speed centrifugal fan drives air through the test section, where the specimen is exposed to a uniform, directional particle-laden air stream. For sand, the fan runs at high speed and the sand is collected in the hopper below the test section, so it is not re-circulated through the fan, as the standard requires. For dust, the sand is removed, the circuit is cleaned and the fan speed is reduced to the dust-test velocity, with the dust kept in suspension in the loop. One machine covers both procedures.

Why it matters: blowing dust reveals penetration into seals, bearings, connectors and filters; blowing sand reveals erosion of housings, lenses, coatings and radomes, and clogging of air paths. Both are required for materiel deployed in desert and unpaved-airfield environments.

Safety: silica flour and quartz sand can cause silicosis – the closed circuit keeps the test media contained; operators use respiratory protection when loading and cleaning.

Uitvoeringen & bestelcodes

Defense Series sizes

DNDC810-MIL-S1 / ORTYDC810-MIL-S1 600 L – 1400 × 900 × 1800 mm – component level
DNDC810-MIL-S2 / ORTYDC810-MIL-S2 1000 L – 1700 × 1100 × 1900 mm – equipment level

Bestelling, kalibratie & garantie

  • Levertijd: tot 35 dagen met Ormity-fabriekskalibratie; tot 60 dagen met ISO/IEC 17025-kalibratierapport (apart gefactureerd).
  • Garantie: 1 jaar, plus levenslange garantie tegen non-conformiteit (exclusief normherzieningen gepubliceerd na de verkoopdatum).
  • Betaling: internationale bestellingen worden 100% vooraf betaald. Alle verkopen zijn definitief na 30 dagen.
  • Verzending: via externe internationale vervoerders; de transittijd hangt af van bestemming, verpakking (kist/pallet) en kalibratietraject. Vraag vóór de bestelling een leveringsraming.
Nog geen beoordelingenDeel je mening. Wees de eerste die een beoordeling achterlaat.

Gerelateerde producten

bottom of page